Questions? Call us at: 877-268-7770 / 954-343-DECO (3326)

Crown Molding Coupling Shell 7 in. H x 6-7/8 in. P x 16-1/2 in. L CMCW-005

Crown Molding Coupling Shell 7 in. H x 6-7/8 in. P x 16-1/2 in. L CMCW-005

$45.99

Molding Type: Coupling.
Measurements: 9-3/4 in. Face x 7 in. Height x 6-7/8 in. Projection x 16-1/2 in. Length.
Finish: White Primer.
Material: Polyurethane.
Brand: Ekena Millwork.

Matching Crown Moldings

CMW-007
CMW-008
CMW-011
CMW-028

-

SKU: CMCW-005 Category: Tags: ,

Description

 

Crown moulding adds a beautiful finish to elegant rooms. To get this look you would simply hire a professional to figure out and install all of the complicated miter cuts. This made the cost of crown moulding more expensive as this method can be labor intensive. Not anymore. Our moulded inside and outside corners make installation a breeze. Say goodbye to miters with our DIY corners and couplers.

  • Makes moulding installation a breeze.
  • Eliminates miter cuts.
  • A true DIY crown moulding installation.
  • Factory primed and ready for paint.
  • Can be painted or faux finished.
  • Lightweight for easy installation.

 

FACE: The distance between the outer contact point with the ceiling to the bottom contact point with the wall.
HEIGHT: The distance between the ceiling and the bottom contact point with the wall.
WIDTH: The distance between the wall and outer contact point with the ceiling.
The FACE is the hypotenuse of the right triangle whose legs are the WIDTH and the HEIGHT.

Additional information

Weight 1 lbs
Dimensions 18 × 9 × 9 in
Molding Type:

Coupling

Style:

Shell

Finish:

White Primer

Face:

9-3/4 in.

Height:

7 in.

Projection:

6-7/8 in.

Length:

16-1/2 in.

Material:

Polyurethane

Product Weight:

1.6 lb.

HOW TO INSTALL CROWN MOLDINGS

 

Step 1: Cut the Corners of the Molding

The hardest part of installing crown molding is cutting the corners. You can’t do it like any other trim pieces because the molding sits at an angle between the wall and the ceiling (Image 1). Using a coping saw (Image 2) is the easiest way to cut the corners because a coped joint is tighter than a mitered joint. A coping saw is also good for a beginner. Any gap in a coped cut can be easily concealed with a little bit of caulk.

Another tool that will make the job easier is a power miter saw (Image 3). It’s accurate and makes a cleaner cut than a plastic miter box.

Step 2: Measure and Mark the Wall

Measure the wall for the length of your first piece of molding. Mark the wall to show the bottom edge of the molding.

Step 3: Cut the First Measured Piece

Once you determine the length, take the molding to the saw and cut in a straight line at a 90-degree angle — you want both ends of the molding to butt against the side walls.

Step 4: Cut the Next Piece to Fit an Inside Corner

Move the miter saw guide to the 45-degree angle point and set the molding into place. The edges need to be pressed firmly against the saw table and the vertical side fence. This is the first key to a straight cut and a good fit.

Step 5: Understand How the Pieces Fit Together

The second key is not so obvious and can be a bit confusing. The molding is upside down, meaning the edge against the vertical fence is the bottom of the molding and the edge against the table is the top of the molding (think of your table as the ceiling).

Step 6: Cut the Molding at a 45-Degree Angle

With the molding in the proper position, use a 10-inch saw blade to cut a perfect 45-degree angle. It is also important here to make sure you cut the molding angle in the right direction: for an inside corner, the bottom of the molding should be longer than the top part of the molding; for an outside corner, the top of the molding will be longer than the bottom.

Step 7: Cope the Joint

When you cope a joint, you scribe the end of one molding to the face of the other. Darken the front edge with a pencil and then use the coping saw to cut as close to the line as you can. You need to hold your thumb against the side of the blade to guide the start of your cut. Start slowly, so you don’t splinter the delicate edge. Cut at a slight angle. You want to cut off more from the edge of the molding and you don’t need to cut it all at one time. Cut out small pieces to make creating this coped joint easier.

Step 8: Check the Fit

Check the fit against a scrap piece of molding to reveal any gaps that need to be trimmed. Use the coping saw to cut off the high points.

Step 9: Attach the Molding to the Wall

Once the fit is right, take the molding to the wall. For a long piece, you’ll need some help holding it. Push the end into the corner, making the fit as tight as possible; attach it to the wall. Use the caulk gun to cover up any gaps in the joint (make sure you’re using paintable caulk). You may need another small piece of molding to finish out the wall.

Step 10: Make Miter Cuts for the Outside Corners

The outside corners should meet exactly (a caulk gun can’t help you much here). Less experienced DIYers may want to paint the crown molding, since paint and caulking can be used to hide any small mistakes — with stained molding, it’s much harder to disguise imperfections.

Step 11: Use Optional Corner Blocks

You can skip the miter and coping cuts altogether by using corner blocks, which will prevent having to cut angles into the molding. It looks professional and tends to be a lot easier.